What is Better to Know When Choosing a Relay?

As a Power Relay Supplier, share with you. When selecting a relay, you must first understand the technical parameters and characteristics of the relay before it can be put into use. Otherwise, the safety and reliability of the relay will not be guaranteed, which will cause the circuit controlled by the Power Relay to be out of control and cause many unnecessary losses in severe cases.
19F Relay
19F Relay
The type of relay contact. The contact type of the relay includes single group contact, double group contact, multiple group contact, normally open contact, normally closed contact, etc., when selecting, it should be selected according to the needs of the load circuit. Blindly pursue the selection of multiple sets of contact type relays.
Relay power. When the relay is actually used, do not connect the contacts of the relay low power load in parallel to control the high power load circuit. This is because the time it takes for the relay contacts to open to close cannot be exactly the same. The group of contacts that have a short operating time after parallel connection will have to bear a large power load, so this group of contacts will be damaged.
Voltage and current of the relay. When the relay is selected for use, the rated voltage of the relay and its pull-in current value should meet the requirements of circuit design, that is, the rated operating voltage value of the coil of the relay is selected according to the size of the driving voltage and current value.
Selection of the nature of the relay supply voltage. There are two types of relays: AC and DC. According to its working power, the choice is to use AC relays or DC relays.
There are two types of relay contacts: normally open contacts (H) and changeover contacts (Z). The control group includes single group, two groups, three groups, etc .; its working principle is very simple, using permanent magnets or using The magnetic field generated by the energized coil can transform its normally open contact action into a normally closed state to turn on the control circuit. In general, the rated capacity of the contacts of a reed switch is very small, and it can only be used as a small control current for the control signal circuit. When used as a control loop signal, there is no rated operating voltage parameter.
Our company also has 19F Relay on sale, please contact us.

评论

发表评论

此博客中的热门博文

How to Buy a Good Relay?

图片
As a  Power Relay Manufacturer , I often meet some customers who say that the quality of your relay is still ok, it is more expensive. Some customers say that I want good quality and cheaper prices. Here, we give everyone a generalization. In fact, the good or bad of Power Relay, 60% is determined by the contacts, reeds, outer casing, thin wire, base, etc. of the relay, and 40% of them are assembled in the relay. Determined in the process. Think about it, if the relay parts are poor, how well the relays are assembled on the production line, and will not make good  PCB Power Relays . Just like a chef, you give him poor raw materials, how good his cooking skills are, and he can't fry good dishes. Therefore, if you have a piece of money and a good quality, it will be more expensive. Power Relay So how do we see the relays are good and bad? If you are interested in researching and taking two different brands, you can see the difference if you study it carefully. Take our relay
阅读全文

What Are The Methods For Relay Debugging?

图片
What are the methods for  Relay Debugging ? The following small series explains for you: 1. Before using the relay, check whether there is any damage caused during transportation. Set the relay to the first setting point, turn the movable system to the magnetic pole direction by hand, and then release it. The movable system should be turned back to the original. Position until the stop. 2. When the relay is re-adjusted, it must be guaranteed: a, the axial movement of the movable system is between 0.15 ~ 0.25mm; b. The air gap between the moving piece and the magnetic pole should be uniform. Under any action, the moving piece and the magnetic pole should not touch each other; c. During the action, the movable system must not be stuck in the middle position; d. When the pointer is rotated from the first scale to the maximum scale, the loops of the hairspring shall not touch each other; e. When the contact is in the open position, the total air gap between the static and dy
阅读全文

Analysis Of The Development Prospects Of Relay Industry

In the past ten years, China's information industry has developed rapidly at a rate three times that of other industries. The communications and automotive industries are also moving forward at a rapid pace. At the same time, the home appliance industry has begun to emerge as an important demand driver. With the overall improvement in the quality of life of Chinese products, more and more consumers are interested in new or upgraded appliances, which in turn stimulates the demand of  Power Relay . According to the forward-looking report of China's current relay industry market foresight and investment planning analysis released by Prospective Industry Research Institute, the use of relays in these industries is considerable. With the development of these industries, it will undoubtedly promote the further expansion of the relay market. In 2010, although the number of relay outlets decreased, the value of exports increased, indicating that the added value of the export relays
阅读全文