Relay is the key to driving a car

The starting relay is the most important and most overlooked part of the car's ignition system. Its role is to redirect the power from the battery to the starter solenoid valve, and then turn on the starter when the engine is idling. Only when the relay is operating normally can you turn the vehicle on and off normally.
Automotive Relay
Automotive Relay
Although you may not encounter the problem of Automotive Relay at present, it is a part about whether your car can drive. Once it is worn out, for your driving safety, please contact professional maintenance personnel to replace it in time.
It is worth noting that most modern cars are equipped with electronic ignition switches activated by a remote control. The electronic chip of the remote control key communicates with the kinetic energy on the car, allowing you to achieve the effect of remote starting. But sometimes the remote control key will affect the relay and convey the wrong error message.
The Automotive Relay Manufacturer lists some symptoms of relay damage or wear. If you notice these similar symptoms, make sure you contact your local professional technician to thoroughly inspect your vehicle as these symptoms may indicate problems with other components as well.
1. The vehicle cannot start.
The most obvious symptom is that when you ignite, the car cannot start, which means that there is something wrong with your relay. The electronic key does not have a manual ignition switch. It works by sending a signal to the relay once the key is inserted or the start button is pressed after power is applied.
Once you can't start the vehicle with the key or electronic key, then there is a high probability that the failure of the relay will cause problems.
Once this kind of problem occurs, you can't start the car no matter how many times you try. When the circuit is not completely damaged, you will hear a click when you start, but no matter what the circuit is, you need to go Perform repairs to ensure driving safety.
2. When the engine is started, the start relay remains connected.
Normally, when you start the engine and release the key or after pressing the start button to start the car. The circuit of the start relay closes and interrupts the power to the start relay.
But when you start the engine, the start relay remains connected, which means that the main contacts of the start relay are likely to be welded together in the closed position.
If the contacts of the start relay are kept connected for a long time, it will cause damage to the starter, circuit, relay and transmission flywheel. In order to stop the loss in time, it needs to be replaced as soon as possible. Our company also has THT Relay on sale, welcome to consult.

评论

发表评论

此博客中的热门博文

How to Buy a Good Relay?

图片
As a  Power Relay Manufacturer , I often meet some customers who say that the quality of your relay is still ok, it is more expensive. Some customers say that I want good quality and cheaper prices. Here, we give everyone a generalization. In fact, the good or bad of Power Relay, 60% is determined by the contacts, reeds, outer casing, thin wire, base, etc. of the relay, and 40% of them are assembled in the relay. Determined in the process. Think about it, if the relay parts are poor, how well the relays are assembled on the production line, and will not make good  PCB Power Relays . Just like a chef, you give him poor raw materials, how good his cooking skills are, and he can't fry good dishes. Therefore, if you have a piece of money and a good quality, it will be more expensive. Power Relay So how do we see the relays are good and bad? If you are interested in researching and taking two different brands, you can see the difference if you study it carefully. Take our relay
阅读全文

What Are The Methods For Relay Debugging?

图片
What are the methods for  Relay Debugging ? The following small series explains for you: 1. Before using the relay, check whether there is any damage caused during transportation. Set the relay to the first setting point, turn the movable system to the magnetic pole direction by hand, and then release it. The movable system should be turned back to the original. Position until the stop. 2. When the relay is re-adjusted, it must be guaranteed: a, the axial movement of the movable system is between 0.15 ~ 0.25mm; b. The air gap between the moving piece and the magnetic pole should be uniform. Under any action, the moving piece and the magnetic pole should not touch each other; c. During the action, the movable system must not be stuck in the middle position; d. When the pointer is rotated from the first scale to the maximum scale, the loops of the hairspring shall not touch each other; e. When the contact is in the open position, the total air gap between the static and dy
阅读全文

Analysis Of The Development Prospects Of Relay Industry

In the past ten years, China's information industry has developed rapidly at a rate three times that of other industries. The communications and automotive industries are also moving forward at a rapid pace. At the same time, the home appliance industry has begun to emerge as an important demand driver. With the overall improvement in the quality of life of Chinese products, more and more consumers are interested in new or upgraded appliances, which in turn stimulates the demand of  Power Relay . According to the forward-looking report of China's current relay industry market foresight and investment planning analysis released by Prospective Industry Research Institute, the use of relays in these industries is considerable. With the development of these industries, it will undoubtedly promote the further expansion of the relay market. In 2010, although the number of relay outlets decreased, the value of exports increased, indicating that the added value of the export relays
阅读全文