Do you know about the small problems of Relays?

　In life, we will use a small micro switch of 0.5a in addition to the tact switch with a current of only 50ma. But today is the T78 Relay, which is often used in automated control circuits. It is actually an "automatic switch" that uses small currents to control high current operation. Therefore, it plays the role of automatic adjustment, safety protection and conversion circuit in the circuit. Relay: An automatic switch that essentially controls a large current with a small current. It has functions and functions such as automatic adjustment circuit, safety protection circuit and conversion circuit.
　　In the process of applying relays, the problems that arise are numerous. So as a Power Relay Manufacturer today, I mainly talk about a problem when using relays: Why are relays often disconnected? Here are the reasons why I sorted them out.
Power Relay
Power Relay
　　1. The load current is greater than the rated switching current of the SSR, which will permanently short the relay. In this case, the SSR with a larger rated current should be used. This is a theoretical statement. In fact, the rated current of the selected relay is not suitable. Simply speaking, when the load is greater than the minimum applicable load, the current can destroy the oxide film on the contact surface, reduce the contact voltage drop, and improve the signal transmission quality; when the load is less than the minimum applicable load, the oxide film and other factors may affect the contact performance of the contact. Although the relay can operate, the signal obtained by the switching is unreliable. Regarding the second problem, the load resistance is 0 ohms, when the voltage is not 0, the theoretical current is infinite, the relay contacts will burn out; if the voltage is 0, there is no signal, this problem has no meaning; the load voltage (this is called the signal voltage more) Appropriate) Small or even close to 0, can be considered as a small signal, suitable for signal relay requirements. The relays used for motor protection on the second floor do not have this requirement. The third floor believes that the principle of use of relays is that the rated current can only be large or small. Under normal circumstances, this statement is correct; but for signal relays, in addition to not higher than the rated current, it can not be lower than the minimum applicable load.
　　2. At the ambient temperature where the relay is located, if the heat is not good, the output semiconductor device may be damaged. In this case, a larger or more effective heat sink should be used. Otherwise it will affect the relay often disconnected
　　3. The line voltage transient causes the SSR output part to pass through. In this case, use a higher rated SSR or provide an additional transient protection circuit.
　　4. The line voltage used is higher than the rated voltage of the SSR.
　　Today, I would like to share with you the problem of frequent breaks in the relay. I hope that everyone can consider it when purchasing relays. If you find these problems after you buy them, you will be wasted your time and resources.
　　Next, let's introduce Power Relay, a device that can be converted in one or more electrical output circuits when input (or excitation) meets certain conditions. It can be used in a neutral point direct grounding system as a directional component for zero sequence current protection.

评论

发表评论

此博客中的热门博文

How to Buy a Good Relay?

图片
As a  Power Relay Manufacturer , I often meet some customers who say that the quality of your relay is still ok, it is more expensive. Some customers say that I want good quality and cheaper prices. Here, we give everyone a generalization. In fact, the good or bad of Power Relay, 60% is determined by the contacts, reeds, outer casing, thin wire, base, etc. of the relay, and 40% of them are assembled in the relay. Determined in the process. Think about it, if the relay parts are poor, how well the relays are assembled on the production line, and will not make good  PCB Power Relays . Just like a chef, you give him poor raw materials, how good his cooking skills are, and he can't fry good dishes. Therefore, if you have a piece of money and a good quality, it will be more expensive. Power Relay So how do we see the relays are good and bad? If you are interested in researching and taking two different brands, you can see the difference if you study it carefully. Take our relay
阅读全文

What Are The Methods For Relay Debugging?

图片
What are the methods for  Relay Debugging ? The following small series explains for you: 1. Before using the relay, check whether there is any damage caused during transportation. Set the relay to the first setting point, turn the movable system to the magnetic pole direction by hand, and then release it. The movable system should be turned back to the original. Position until the stop. 2. When the relay is re-adjusted, it must be guaranteed: a, the axial movement of the movable system is between 0.15 ~ 0.25mm; b. The air gap between the moving piece and the magnetic pole should be uniform. Under any action, the moving piece and the magnetic pole should not touch each other; c. During the action, the movable system must not be stuck in the middle position; d. When the pointer is rotated from the first scale to the maximum scale, the loops of the hairspring shall not touch each other; e. When the contact is in the open position, the total air gap between the static and dy
阅读全文

Analysis Of The Development Prospects Of Relay Industry

In the past ten years, China's information industry has developed rapidly at a rate three times that of other industries. The communications and automotive industries are also moving forward at a rapid pace. At the same time, the home appliance industry has begun to emerge as an important demand driver. With the overall improvement in the quality of life of Chinese products, more and more consumers are interested in new or upgraded appliances, which in turn stimulates the demand of  Power Relay . According to the forward-looking report of China's current relay industry market foresight and investment planning analysis released by Prospective Industry Research Institute, the use of relays in these industries is considerable. With the development of these industries, it will undoubtedly promote the further expansion of the relay market. In 2010, although the number of relay outlets decreased, the value of exports increased, indicating that the added value of the export relays
阅读全文