Why is Power Relay Disconnected Frequently?

In the process of applying Power Relay, there are many problems. So today is mainly about a problem that arises when using relays: Why are relays disconnected frequently? Here are the reasons why the Automotive Relay Manufacturer is organized.
1. The load current is greater than the rated switching current of the SSR, which will permanently short the relay. In this case, the SSR with a larger rated current should be used. This is a theoretical statement. In fact, the rated current of the selected relay is not suitable.
Simply speaking, when the load is greater than the minimum applicable load, the current can destroy the oxide film on the contact surface, reduce the contact voltage drop, and improve the signal transmission quality; when the load is less than the minimum applicable load, the oxide film and other factors may affect the contact performance of the contact. Although the relay can operate, the signal obtained by the switching is unreliable.
Power Relay
Power Relay
2. At the ambient temperature of the Power Relay, if the heat is not good, the output semiconductor device may be damaged. In this case, a larger or more effective heat sink should be used. Otherwise it will affect the relay to disconnect frequently.
3. The line voltage transient causes the SSR output part to pass through. In this case, use a higher rated SSR or provide an additional transient protection circuit.
4. The line voltage used is higher than the rated voltage of the SSR.
Our company specializes in High Sensitivity Relay. If you want to know more details, please pay attention to our website or feel free to contact us.

评论

发表评论

此博客中的热门博文

How to Buy a Good Relay?

图片
As a  Power Relay Manufacturer , I often meet some customers who say that the quality of your relay is still ok, it is more expensive. Some customers say that I want good quality and cheaper prices. Here, we give everyone a generalization. In fact, the good or bad of Power Relay, 60% is determined by the contacts, reeds, outer casing, thin wire, base, etc. of the relay, and 40% of them are assembled in the relay. Determined in the process. Think about it, if the relay parts are poor, how well the relays are assembled on the production line, and will not make good  PCB Power Relays . Just like a chef, you give him poor raw materials, how good his cooking skills are, and he can't fry good dishes. Therefore, if you have a piece of money and a good quality, it will be more expensive. Power Relay So how do we see the relays are good and bad? If you are interested in researching and taking two different brands, you can see the difference if you study it carefully. Take our relay
阅读全文

What Are The Methods For Relay Debugging?

图片
What are the methods for  Relay Debugging ? The following small series explains for you: 1. Before using the relay, check whether there is any damage caused during transportation. Set the relay to the first setting point, turn the movable system to the magnetic pole direction by hand, and then release it. The movable system should be turned back to the original. Position until the stop. 2. When the relay is re-adjusted, it must be guaranteed: a, the axial movement of the movable system is between 0.15 ~ 0.25mm; b. The air gap between the moving piece and the magnetic pole should be uniform. Under any action, the moving piece and the magnetic pole should not touch each other; c. During the action, the movable system must not be stuck in the middle position; d. When the pointer is rotated from the first scale to the maximum scale, the loops of the hairspring shall not touch each other; e. When the contact is in the open position, the total air gap between the static and dy
阅读全文

Analysis Of The Development Prospects Of Relay Industry

In the past ten years, China's information industry has developed rapidly at a rate three times that of other industries. The communications and automotive industries are also moving forward at a rapid pace. At the same time, the home appliance industry has begun to emerge as an important demand driver. With the overall improvement in the quality of life of Chinese products, more and more consumers are interested in new or upgraded appliances, which in turn stimulates the demand of  Power Relay . According to the forward-looking report of China's current relay industry market foresight and investment planning analysis released by Prospective Industry Research Institute, the use of relays in these industries is considerable. With the development of these industries, it will undoubtedly promote the further expansion of the relay market. In 2010, although the number of relay outlets decreased, the value of exports increased, indicating that the added value of the export relays
阅读全文