Relay characteristics parameters terminology

1.Insulation resistance: it is the impedence when the conductors insulated with insulating material are applied to voltage and it is generally shown in "MΩ". The speculated voltage discribed above are general 500Vd.c.(or 250Vd.c.).

2.Dielectric strength: it is the voltage value when, within the speculated time, the conductors insulated with insulated material are applied to the voltage and the leakage current is less than the speculated current. The certain voltage above generally is the effective value of AC voltage and unless otherwise stated, the leakage current is generally less than 1mA.

3.Operation time: it refers to, with the relay in the released state, the elapsed time from the initial application of power to the coil, till the closure of the normal open contacts. It does not include any bounce time, and expressed in "ms".

4.Release time: it refers to, with the relay in the operation state, the elapsed time from the initial removal of coil power till the re-close of the normal closed contacts. It doesn't include bounce time and expressed in "ms".

5.Bounce time: it generally refers to the time from the initial close of the contacts till the complete close and generally expressed in "ms".

6.Switching frequency: it refers to the cycling times of the operation and release in united time.

7.Ambient temperature: it refers to the temperature in which the relay can normally be applied and it is generally expressed in the range of temperature.

8.Coil temperature rise: it refers to the temperture that the coil rises by after the temperature becomes stable and under the conditions that in the suitable maximum ambient environment the rated voltage is impressed on the coil and the rated load is impressed on the contacts. Generally it refers to the maximum value, expressed in "K".

9.Humidity: it refers to the required humidity in which the relay can reliably work and generally expressed in relative humidity "%RH".

10.Model of the terminals: the terminals model of the relays also shows the application fields. Generally speaking, the models of terminals are PCB,THT,SMT,Plug-in,QT and others.

11.Enclosure type: it refers to the protection mode for the relay body. It is divided into open type,dust proofed,flux proofed and sealed types.
More information please view here.

评论

发表评论

此博客中的热门博文

How to Buy a Good Relay?

图片
As a  Power Relay Manufacturer , I often meet some customers who say that the quality of your relay is still ok, it is more expensive. Some customers say that I want good quality and cheaper prices. Here, we give everyone a generalization. In fact, the good or bad of Power Relay, 60% is determined by the contacts, reeds, outer casing, thin wire, base, etc. of the relay, and 40% of them are assembled in the relay. Determined in the process. Think about it, if the relay parts are poor, how well the relays are assembled on the production line, and will not make good  PCB Power Relays . Just like a chef, you give him poor raw materials, how good his cooking skills are, and he can't fry good dishes. Therefore, if you have a piece of money and a good quality, it will be more expensive. Power Relay So how do we see the relays are good and bad? If you are interested in researching and taking two different brands, you can see the difference if you study it carefully. Take our relay
阅读全文

What Are The Methods For Relay Debugging?

图片
What are the methods for  Relay Debugging ? The following small series explains for you: 1. Before using the relay, check whether there is any damage caused during transportation. Set the relay to the first setting point, turn the movable system to the magnetic pole direction by hand, and then release it. The movable system should be turned back to the original. Position until the stop. 2. When the relay is re-adjusted, it must be guaranteed: a, the axial movement of the movable system is between 0.15 ~ 0.25mm; b. The air gap between the moving piece and the magnetic pole should be uniform. Under any action, the moving piece and the magnetic pole should not touch each other; c. During the action, the movable system must not be stuck in the middle position; d. When the pointer is rotated from the first scale to the maximum scale, the loops of the hairspring shall not touch each other; e. When the contact is in the open position, the total air gap between the static and dy
阅读全文

Analysis Of The Development Prospects Of Relay Industry

In the past ten years, China's information industry has developed rapidly at a rate three times that of other industries. The communications and automotive industries are also moving forward at a rapid pace. At the same time, the home appliance industry has begun to emerge as an important demand driver. With the overall improvement in the quality of life of Chinese products, more and more consumers are interested in new or upgraded appliances, which in turn stimulates the demand of  Power Relay . According to the forward-looking report of China's current relay industry market foresight and investment planning analysis released by Prospective Industry Research Institute, the use of relays in these industries is considerable. With the development of these industries, it will undoubtedly promote the further expansion of the relay market. In 2010, although the number of relay outlets decreased, the value of exports increased, indicating that the added value of the export relays
阅读全文